How To Fix A Wet Battery That Can't Save A Strum: Apply These 6 Ways

Cara memperbaiki aki wet yang tidak bisa menyimpankan sumpar (image ajcbattery)

YOGYAKARTA - Knowing how to fix a wet battery that can't store a stun is very important when the battery begins to experience a decline in performance. If wet batteries are no longer able to store the stun, it means that there is a problem with the components in it that need to be repaired immediately.

The condition of the battery that is not functioning properly can hamper the supply of electricity to the vehicle engine, so the car cannot be turned on. This problem is certainly a hassle, especially if it happens suddenly. Therefore, it is important to understand the improvement steps so that the battery can return to optimal work.

For those who don't know how to handle it, don't worry. This article will discuss practical solutions that can be applied to fix wet batteries that are experiencing problems. Check out the full guide below!

1. Tool Preparation

Before starting to repair wet batteries that can't store stuns, make sure to prepare all the necessary equipment. With complete tools, the repair process will be easier and safer. Some of the tools needed include:

2. Get a Wet Aki

Once all the equipment is ready, the first step that must be taken is to remove the wet battery from the vehicle. Make sure to do it carefully so as not to damage the battery components or other parts of the car.

Once removed, place the battery on a stable and safe surface. This is important to prevent the battery from rolling over or falling, which can cause further leakage or damage.

Placing the battery on a flat area also helps ease the repair process. With a stable position, users can be more flexible when taking the next step in how to fix wet batteries that cannot store stuns.

3. Placing the battery in the Right Location

After the wet battery is placed in a safe and flat place, the next step is to open the cover. If there is a seal on the top of the battery, the seal needs to be cut with a knife carefully, starting from the edge.

Once the seal is successfully removed, the user will see several cells in the wet battery. Each of these cells plays an important role in storing and delivering the electricity needed by the vehicle.

The next step is to open the covers of each battery cell. That way, users can continue the next process in a way to fix a wet battery that can't store the stun, which is to throw the old battery water away before replacing it with a new one.

4. Use Old Aki Water

To get rid of the old battery water, you need to install a pipette or syringe on each wet battery cell. Take out the old battery water until about 30 to 40 percent is left in the cell. Don't completely empty it so that the battery recharge process remains easy.

The water that has been issued should be stored in a glass container to prevent harmful effects on the environment, because this liquid contains corrosive substances.

Next, dissolve the USP Magnesium Sulfate in boiling water, then mix it with the new battery water. Stir until the solution is mixed evenly. After that, insert the mixture into each wet battery cell using a pipette or syringe.

5. Fill in the Wet Battery in the Battery

After the battery is fully charged, carry out battery charging using a battery charger. It is better not to immediately close the cells and wet battery during the charging process.

Letting the battery cells open during charging aims to make the air come out smoothly. If the battery condition is severe enough, it is advisable to charge throughout the night so that the results are more optimal.

If you don't have a battery charger, another alternative that can be used is filling through an alternator. For this method, make sure the battery and wet battery cells have been closed again before installing them into the car.

In addition, you can replace the battery cell cover with a new one if needed. After the battery is re-installed in the car, immediately turn on the vehicle so that the alternator can charge the battery more effectively.

6. Use gloves

Sebagai langkah terakhir dalam memperbaiki aki wet yang tidak dapat menyimpankan stun, pastikan untuk selalu menggunakan sarong tangan.

The use of gloves serves to maintain the hygiene of hands so that they remain hygienic during the repair process. In addition, gloves also protect hands from sparks of aki water that can be harmful to the skin.

Untuk menambah refrensi per-aki-an, baca juga: Cara Jumper Aki Mobil Yang Benar

So after knowing how to fix wet batteries that can't store stuns, see other interesting news on VOI.ID, it's time to revolutionize news!